• 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB
  • 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB
3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB
Specifications:
Product Name    : Ramps 1.6 Plus
Size                       : 101.6*60.19MM
PCB                      : 4-layer Board
Current                 : 30A
Support Driver    : A4988 / DRV8825 / TMC2100 / TMC2208 / TMC2130


 
Description:

Ramps 1.6 plus is mainly a new adapter ramps board for the upgrade of the old Ramps1.6 driver using the SPI working mode wiring complex problem.The Ramps 1.6 plus uses the SPI mode of operation, which can be achieved simply by plugging and unplugging the jumper cap. It not only saves the complicated wiring process, but also saves the cost of external wiring, which is economical and practical.

The new ramps 1.6 plus effectively avoids the problem of the motor not working by inserting the wrong line; It also avoids the problem that the drive does not work due to poor contact of the external line during the printing process.


Advantage:


1. The PCB has a built-in selection terminal for driving the SPI working mode, and is compatible with STEP/DIR and SPI modes.


2. The parts of power and heat bed using the 30A high current terminal ,which can largely avoid the burning terminal situations.


3. It is more clear to connect the wire after update a new top overlay and bottom overlay .


4.Adding the reset expansion interface,It is convenient for users to extend the reset button.


5. X, Y, Z, E0, E1 all use parallel dual motor interface, so that the board can use for more type machine .


6, Using a combination of color pin and row connector , effectively distinguishing each function interface, beautiful and practical.



Driver SPI and STEP/DIR working mode selection



SPI working model :


When using driver SPI model : connect 1 and 11,2 and 12, 3 and 5 ,4and 6 respectively, using four pcs 13 (short circuit caps)
SPI is the serial bus mode of operation, where 1 connection 11 is MOSI, 2 connection 12 is SCK, 3 connection 5 is CSN, and 4 connection 6 is MISO; ( Corresponding picture indication)



STEP/DIR (stepper/ directional drive mode):


Figure 11, 12 and 5 respectively represent MS1, MS2 and MS3 of STEP/DIR mode (subdivided selection end),8, 9 and 10 are all VCC (high level);Take the LV8729 driver as an example. Connect 5 (MS3) and 8 (high level) by using a 13 (short-circuit cap),The driver works in STEP/DIR mode and it is 16 subdivisions.


Note:The interpolation of MS1, MS2, MS3 and 8, 9, 10 in STEP/DIR mode is selected according to different subdivisions of different drivers.


 


 


Attention:

1. The driver working mode selection determines the firmware to be programmed. When the SPI mode is selected, the motherboard must be programmed with the SPI working mode firmware(For a tutorial on changing the SPI firmware, please refer to the BIGTREETECH TMC2130 V1.1 Instruction Manual.);When selecting the STEP/DIR mode, the firmware must be replaced with the firmware of the STEP/DIR working mode, and the consistency of the subdivision must be observed.(Firmware is 16 subdivisions, Ramps1.6 plus must also choose 16 subdivisions)


2. When using the heatbed with power over 140W,please be sure to install MOS radiator to prevent overheating and burning; When using the heatbed with power over 180W, please be sure to select heatbed MOS module for transfer to avoid the board burning due to long-time overheating;


3. When you plug and unplug the drive into Ramps1.6 plus, please pay attention to the direction of the drive. It should not be inserted in reverse to prevent the drive from burning, and the operation of the plug and unplug drive must be conducted under the premise of power failure.


4. Description of each driver SPI mode CS pin: (For details, please refer to the data RAMPS1.6 plus PIN)


XCS:D63 YCS:D40 ZCS:D42 E0CS:D65 E1CS:D66


Product Description

Buy 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB From ElectronicsBD Bangladesh (BD)

In Bangladesh, you can get the best Quality and original 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB from ElectronicsBD. We have a large collection of the latest 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB to purchase. Order online or visit our shop ElectronicsBD to get yours at the lowest price.

What is the latest and best price of 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB in Bangladesh (BD) ?

The latest and special price of 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB in Bangladesh is BDT ৳1,250.00 Taka. Buy best quality 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB from ElectronicsBD at a special price in Bangladesh (BD). You can buy 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB at best price from ElectronicsBD or visit ElectronicsBD Store. বাংলাদেশে আকর্ষণীয় মূল্যে কিনুন 3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB শুধুমাত্র ইলেকট্রনিক্স বিডি ElectronicsBD থেকে। ElectronicsBD বাংলাদেশের সকল প্রধান স্থান যেমন বরিশাল, চট্টগ্রাম, ঢাকা, খুলনা, রাজশাহী, রংপুর, ময়মনসিংহ এবং সিলেটে পণ্য ডেলিভারি করে ।

Sojib 29/08/2022

product quality onek valo

Bazlur 29/06/2022

Thank you guys.

Emran Hossain28/06/2022

গতকাল ডেলিভারি পেয়েছি।

Tanvir 29/03/2022

ektu fast delivery dile valo hoto

Tahmid 21/03/2022

They are the best where you can find your robotics equipment.

Write a review

Note: HTML is not translated!
Bad           Good
Captcha
3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB

3D Printer parts Ramps 1.6 Plus Board upgrade base on Ramps 1.6 1.5 1.4 Control Board 4 layers PCB

৳1,250.00