Digital IC

Contains a divide-by-two Section and a divide-by-eight SectionSections Can be Combined to form BCD, modulo-12 or modulo-16 CountersLow Power DissipationOperating Temperature up to 70oCStandard TTL Switching Voltages..

Specifications:Op-amp coupled with MOSFET at outputWide power supply RangeSinge supply – 5V to 16VDual supply – ±2.5V to ±8VInput Terminal current: 1mAMaximum Output Voltage: 13.3VMaximum source current: 22mAMaximum sink current: 20mASupply current: 10mACommon Mode Rejection Ration (CMRR): 80dBPacka..

CD4011B, CD4012B, and CD4023B NAND gates provide the system designer with direct implementation of the NAND function and supplement the existing family of CMOS gates. All inputs and outputs are buffered.The CD4011B, CD4012B, and CD4023B types are supplied in 14-lead hermetic dual-in-line ceramic pac..

Quad Bilateral Switch for MultiplexingOperating Voltage: 3V to 18VSwitching Voltage: 20V (maximum)On-state Resistance: 200Ω (at 15V Vcc and 10kΩ Load)Output current High: -0.4mALow Level Control pin Voltage: 0.9V (max)High Level Control pin Voltage: 11V (min @ 15V Vcc)Available in 14-pin PDIP, GDIP,..

The IC CD4017 is used for counting applications, it has the capability to turn on 10 outputs sequentially in a pre-defined time and reset the count or hold it when required. It also has the capability to indicate the status of counting using Carry pin. This is commonly used for Led chasers..

CD4011B, CD4012B, and CD4023B NAND gates provide the system designer with direct implementation of the NAND function and supplement the existing family of CMOS gates. All inputs and outputs are buffered.The CD4011B, CD4012B, and CD4023B types are supplied in 14-lead hermetic dual-in-line ceramic pac..

CD4027 - Dual J-K Master/Slave Flip-Flop with Set and ResetThe CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits constructed with N- and P-channel enhancement mode transistors. Each flip-flop has independent J, K, set, reset, and clock inputs&nbs..

Specifications:DC Supply Voltage: -0.5V to +20VDC Input Current: 10mAOperating Temperature Range: -55°C to +125°CFeatures:Operative in high voltage as 20VBoth the counter and decoding in a single ICIdeal for low power displaysApplication:Decade Counter of 7 Segment Decimal DisplayClocksDigital Watch..

CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input. A 5.2-V zener diode is provided for supply regulation if necessary.The CD4046B..

We can use the IC in both Astable and Monostable mode, for making different circuit. The IC can be used for generating clock pulse, sine wave, square wave and many others. It can also be used in application of timing delay circuits, frequency multiplier and frequency divider. To generate an envelope..

CD4093B consists of four Schmitt-trigger circuits. Each circuit functions as a two-input NAND gate with Schmitt-trigger action on both inputs. The gate switches at different points for positive- and negative-going signals. The difference between the positive voltage (VP) and the negative voltage (VN..

Specifications:Supply voltage ranges from 3v to 18vSet-up-time is 150, 70, and 40ns at 5v, 10v, and 15v respectivelyStrobe pulse width is 400, 160, and 100ns at 5v, 10v, and 15v respectivelyHold time is zero100% tested for quiescent current at 20vHaving high input current of 1uA (max.) at 18vMaximum..

CD4541B programmable timer consists of a 16-stage binary counter, an oscillator that is controlled by external R-C components (2 resistors and a capacitor), an automatic power-on reset circuit, and output control logic. The counter increments on positive-edge clock transitions and can also be reset ..

The DS1302 trickle-charge timekeeping chip contains a real-time clock/calendar and 31 bytes of static RAM. It communicates with a microprocessor via a simple serial interface. ... The DS1302 is designed to operate on very low power and retain data and clock information on less than 1µW...

The DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I2C, bidirectional bus...

The Microchip Technology Inc. ENC28J60 is a standalone Ethernet controller with an industry standard Serial Peripheral Interface (SPI™). It is designed to serve as an Ethernet network interface for any microcontroller equipped with SPI.  Communication with the microcont..

The HCF4094 is a monolithic integrated circuit fabricated in metal oxide semiconductor technology available in an SO-16 package. The HCF4094 is an 8-stage, serial shift register having a storage latch associated with each stage for strobing data from the serial input to parallel buffered 3-state out..

ICL-7660 CMOS Voltage Converter.DescriptionSimple Conversion of +5V to ±5V SuppliesSimple Voltage MultiplicationTypical Open Circuit Conversion Efficiency 99.9%Wide Supply Range 1.5V to 10VMinimal External Components Required..

ICL-7107 3+1/2 Digit LED Driver with A/D.FeaturesGuaranteed Zero reading for 0V InputTrue Polarity at Zero1pA Typical Input CurrentLow NoiseOn Chip Clock and ReferenceICL7107CPL Datasheet..

SPECIFICATIONS:SMPS ControllerOutput Current: 500mAReference Output Current: 50mAOscillator Charging Current: 5mAPower Dissipation: 1000mWReference Output Voltage: 501VLine Regulation: 9mVLoad Regulation: 20mVMaximum Oscillator Frequency: 430KHzPackage: DIP-16..

The L298 is an integrated monolithic circuit in a 15-lead Multiwatt and Power SO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels anddrive inductive loads such as relays, solenoids, DC and stepping motors. Two ena..

The LM111, LM211, LM311 are voltage comparators that have low input currents. They are also designed to operate over a wide range of supply voltages: from standard ±15V operational amplifier supplies down to the single +5V supply used for IC logic...

These circuits consist of four independent, high gain, internally frequency compensated operational amplifiers .They operate from a single power supply over a wide range of voltages.Operation from split power supplies is also possible and the low power supply current drain is independent of the magn..

DescriptionMAX232  RS-232 Driver/Receiver Manufacturer:Maxim IntegratedProduct Category:RS-232 Interface ICRoHS: DetailsFunction:TransceiverData Rate:120 kb/sNumber of Drivers:2 DriverNumber of Receivers:2 ReceiverSupply Voltage – Max:5.5 VOperating Supply Voltage:5 VSupply Voltage – ..

The MAX7219ENG are compact, serial input/output common-cathode display drivers that interface microprocessors (µPs) to 7-segment numeric LED displays of up to 8 digits, bar-graph displays, or 64 individual LEDs.Features:10MHz Serial InterfaceIndividual LED Segment ControlDecode/No-Decode Digit Selec..

Features 16-bit input/output port expander with interrupt outputCascadable for up to 8 devices on one bus25mA sink/source capability per I/OSupports up to 10MHz SPI™ clock speeds..

The MT8870D/MT8870D-1 is a complete DTMF receiver integrating both the bandsplit filter and digital decoder functions. The filter section uses switched capacitor techniques for high and low group filters; the decoder uses digital counting techniques to detect and decode all 16 DTMF tonepairs into a ..

A ULN2803 is an Integrated Circuit (IC) chip with a High Voltage/High Current Darlington Transistor Array. It allows you to interface TTL signals with higher voltage/current loads. In English, the chip takes low level signals (TLL, CMOS, PMOS, NMOS – which operate at low voltages and low currents) a..

ULN2804 contains eight darlington transistors with common emitters and integral suppression diodes for inductive loads. Each darlington features a peak load current rating of 600mA (500mA continuous) and can withstand atleast 50V in the off state. Outputs maybe paralleled for higher current capabili..