Sensors

Description ZFM-60 integrated optical fingerprint module is a ultra-low power module with touch-sensitive.ZFM-60 is very effective fingerprint module.This biometric fingerprint module can be powered with DC 3.6 ~ 6.0V. Current consumption of this module is low.Specifications Supply vo..

Operating voltage:3.3V-5VUsing LM393 comparator with wide voltageA small panel output interface can be directly connected with the micro controller IO portWith an adjustable precision potentiometer to adjust the sensitivityThe flame sensor is most sensitive to flame and it will also respond to ordin..

This inertial-measurement-unit combines 3 of the best quality sensors available on the market to give you 11 axes of data: 3 axes of accelerometer data, 3 axes gyroscopic, 3 axes magnetic (compass), barometric pressure/altitude and temperature. We tested many different ‘combination’ sensors and foun..

Specifications:Size: 19*18mm (2mm fixing hole)Voltage: 3.3-5VPressure: 0-40KPaThis module adopts high precision AD sampling chip and 0-40KPa air pressure sensor. And it can connect 2.5mm soft tube and detect the water level and other air pressureAdopt 5K ohm resistor bridge sensor, and specific air ..

Specifications:Item Type: Solar Lamp Circuit BoardModel Specifications: YX-402Product Size: Approx. 19 x 59mm / 0.7 x 2.3inInduction Method: Human infrared sensorSensing Distance: 2-5 meters (depending on the sensing ambient temperature)Induction Time: 25 secondsBattery Input: 3.7V / 3.2VThis contro..

Specification:Working voltage: 3.3 V to 5 V DCThe working current, try to choose more than 1 a power supplyThe working temperature: - 10 °C - + 50 °CInstall the aperture: M3 screwsThe detection distance: 1 mm and 60 cm adjustable, the closer distance performance more stable, white reflection furthes..

This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. The sensor is a group of half-bridge strain gauge, there are 3 ways to use it. This module uses 24 high precision A/D converter chip hx711, specially designed for the high precision electronic scale...

Features:Supports Gravity 3-Pin interfaceAnalog output Applications:Garden plantsMoisture detectionIntelligent agriculture Specifications:Operating Voltage: 3.3 ~ 5.5 VDCOutput Voltage: 0 ~ 3.0VDCInterface: PH2.0-3PDimension: 98mm * 23mm (3.86in x 0.905in)Weight: 15g..

Product parameters:Working voltage: 2.4V-3.6VMeasuring range: 4-8in (10-20CM)Interface type: I2C interfacePin description:INT : interrupt outputSCL: I2C clock portSDA: I2C data portVCC: power supply positive input port, connect 2.4V-3.6V voltage (3.3V recommended)GND: power supply negative inputVL: ..

Specifications:Model: AS5600Operating Temperature Range : -40°C to 125°CPower supply: 3.3V DCLength: 23mmHeight: 3 mmWidth: 22.5mmPackage:1x AS5600 Magnetic Encoder Induction Angle Sensor..

Specifications:BH1750 FeaturesPower Supply: 2.4V-3.6V (typically 3.0V)Less current consumption: 0.12mAMeasuring Rang: 1-65535lxCommunication: I2C busAccuracy: +/-20%Built in A/D converter for converting analog illuminance in the digital data.Very small effect of IR radiationHighly responsive near to..

Specifications:Model: GY-652The use of chip: HMC5983 + BMP180Power supply :3-5v (internal low dropout regulator)Communication modes: standard IIC communication protocol)Magnetic field range: ± 0.88 to ± 8.1 gaussPressure Range :300-1100hPaChip 12bit AD converter, 16-bit data outputMachine welding pr..

Feature:It is integrated no.5 high sensitivity tracking sensor, for the environmental impact of small, can accurate tracking to complex black line (white line), for the simple black line tracking more comfortable.It is integrated infrared barrie sensor, escapes distance can be regulated through the ..

Detectable Gases:Carbon monoxide CO 1-1000ppmNitrogen dioxide NO2 0.05-10ppmEthanol C2H5OH 10-500ppmHydrogen H2 1-1000ppmAmmonia NH3 1-500ppmMethane CH4 >1000ppmPackage:1x CJMCU-4541 MICS-4514 Carbon Monoxide Nitrogen Oxygen Sensor CO/NO2/H2/NH3/CH4..

Specifications:Imported chips TCS3200 PCB board with gold platingTCS3200 is TCS230 upgrade version, the betterPower supply 3-5vAnti-light interferenceWhite LED, can control the on and off.Can detect non-luminous object colorPCB dimensions: (L) 33mm * (W) 25mm Package:1x Color Sensor Recogn..

Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on ..

Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on ..

Features:Sensor module for measuring current. Both AC and DC, up to 5A can be measured. The output is a linear voltage between 0 – VCC, centered around VCC/2 at 0A. The load is connected in series to the screw terminal.Specifications:Dimensions: 31 x 13mmSupply voltage: 5VSensitivity: 185mV/ASensor:..

Specifications:Dimensions: 27 x 14 x 13 mm .Weight: 4 gm.Input Voltage range: DC0 to 25 VVoltage detection range: DC 0.02445 V to 25 VAnalog Voltage resolution : 0.00489 VOutput Interface : “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pinsDC input interface: red terminal positi..

SPECIFICATION:Operating Voltage: 5V DCOperating Current: 40mA (MAX)Response Time: <500msInsulation Resistance: 100M (Min)Output Method: AnalogAnalog output: 0-4.5VDigital Output: High/Low level signal (you can adjust the threshold value by adjusting the potentiometer)Operating Temperature: 5℃~90 ..

DHT11 Specifications:Operating Voltage: 3.5V to 5.5VOperating current: 0.3mA (measuring) 60uA (standby)Output: Serial dataTemperature Range: 0°C to 50°CHumidity Range: 20% to 90%Resolution: Temperature and Humidity both are 16-bitAccuracy: ±1°C and ±1%Where to use DHT11:The DHT11 is a comm..

DHT22/AM2302 Digital Temperature Humidity Measurement Sensor Module.Description:1.Type:AM2302 2.Accuracy resolution:0.1 3.Humidity range:0-100%RH 4.Temperature range:-40~80? 5.Humidity measurement precision:±2%RH 6.Temperature measurement precision:±0.5? 7.4-pin package..

Specifications:Material: non-woven fabricColor: As the picture showSize: As the picture show(1inch = 2.54cm)Package:1Set AD8232 Monitor Kit..

Electronic vibration sensor 801SW: 10mmH: 7mm..

DescriptionThe Advance Technologies EMG Muscle Sensor V3.0 With Cable And Electrodes will measure the filtered and rectified electrical activity of a muscle; outputting 0-Vs Volts depending the amount of activity in the selected muscle, where Vs signifies the voltage of the power source. Power suppl..

DescriptionDive into biometric security with this easy to use fingerprint sensor! This fingerprint sensor simplifies the process of fingerprint detection, storage, and verification. Inside the sensor is a high power DSP chip that does all image rendering, calculation, feature finding, and searching...

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove. The resistance of the flex sensor changes when the metal pads are on th..

Description: Usage is very simple Single : As long as there are serial microcontroller , embedded can operate this module, MSP430 , 51 , AVR , PIC , the STM32,ARM,FPGA,the Arduinocontroller,pcDuino and so can operate this module. This module through the serial port control, you can also use the..

Specifications:Dimensions:  24mm x20mm x9.8mmWeight:  G.W 29gBattery:  ExcludeInput Voltage:  5V/3.3VFeaturesDetects conductance of skinFinger Straps for electrodes..

Grove water sensor module is part of the Twig system. This sensor works by having a series of exposed traces connected to ground and interlaced between the grounded traces are the sens traces. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value ..

Specifications:Chip: MPU-6050Power supply: 3v-5V power +Gyroscope range: + 250 500 1000 2000 ° / sAcceleration range: ± 2 ± 4 ± 8 ± 16 gCommunication: standard IIC communication agreement Chip built-in 16 bit AD converter, 16 bits of data outputPin spacing 2.54 mm Package:1x GY 521 Tr..

Specifications:Chip: TCS3200Input voltage: DC 3 ~ 5VOutput frequency voltage: 0 ~ 5VUse bright white LED lightsCan be connected directly with MicrocontrollerStatic detection of the measured object colorBest detection distance: 10mmSize:3.3x3.3x2.5cm(approx)Package :1 x  GY-31 TCS3200 Color Sens..

Specifications:1.8V to 3.6V Supply VoltageLow power consumption - 0.5uA at 1HzI2C interfaceMax I2C Speed: 3.5MhzVery low noise - up to 0.02hPa (17cm)Full calibratedPressure Range: 300hPa to 1100hPa (+9000m to -500m)Package1x GY-68 BMP180 Digital Barometric Pressure Sensor Module..

DescriptionME-BME/BMP280 is a Breakout Board featuring a Bosch Sensortec ME/MP280 Temperature, Humidity & Pressure Sensor. The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.Default setting of the board; si..